Belong Router Login
Belong provides NBN internet services, typically with a pre-configured modem. This guide helps you access your Belong modem's web interface to manage settings like WiFi passwords.
How to Login to Belong Router
Accessing your Belong modem's settings allows customization of your home network. Belong commonly uses modems (like the Technicolor TG series) with a specific default gateway address.
The standard IP address to reach the Belong modem interface is 10.0.0.138. Ensure your device is connected to the modem's network before entering this address in your browser.
The default login credentials are typically Username: admin and Password: Belong (note the capitalization). If these don't work, check any documentation that came with your modem or contact Belong support, as they may have been changed.
- Connect a device (computer/tablet) to your Belong modem's network using WiFi or an Ethernet cable.
- Open a web browser (Chrome, Edge, Firefox).
- In the address bar, type 'http://10.0.0.138' and press Enter.
- The Belong modem login page should appear.
- Enter 'admin' for the username.
- Enter 'Belong' (with a capital B) for the default password.
- Click 'Login'.
Default IPs, username and password for Belong
| Router Brand | IP | Username | Password | Confidence |
|---|---|---|---|---|
| Belong | 10.0.0.138 | admin | password | 80% |
| Belong | 192.168.20.1 | admin | admin | 80% |
Popular Router Models using Belong
| Model | IP | Username | Password |
|---|---|---|---|
| Technicolor TG799vac | 10.0.0.138 | admin | password on device |
| Sagemcom F@st 4315 | 10.0.0.138 | admin | password on device |
Troubleshooting Issues with Belong Router
Can't log in to your Belong modem? Try these steps:
- Verify Network Connection: Make sure your device is connected to the Belong WiFi network or plugged in via Ethernet.
- Correct IP Address: Confirm you are using '10.0.0.138'. Double-check for typos.
- Check Credentials: Ensure you're using 'admin' (lowercase) for the username and 'Belong' (capital B) for the password. Passwords are case-sensitive.
- Power Cycle Modem: Turn off the modem, wait about 30 seconds, then turn it back on. Allow a few minutes for it to fully boot up before trying to log in again.
- Clear Browser Cache: Try clearing your browser's cache and cookies, or use a private/incognito browser window.
- Factory Reset (Caution): Locate the reset button (usually a small pinhole) on the back or bottom of the modem. Press and hold it for 15-20 seconds while the modem is powered on. This will erase all settings, including custom WiFi passwords, and revert to defaults (admin/Belong). You might need to re-enter NBN details if applicable (though often automatic).
Belong Router setup
Once logged in to your Belong modem, here are common setup tasks:
- Change Admin Password: It's highly recommended to change the default 'Belong' admin password for security. Look for options under Administration or Security.
- Change WiFi Password: Navigate to the Wireless or WiFi settings section to change your WiFi network password (WPA Key). Use a strong password.
- Customize WiFi Name (SSID): You can also change the name of your WiFi network in the same section.
- Check Internet Connection Status: Verify your NBN connection status under WAN or Internet settings.
- Review Connected Devices: See a list of devices currently connected to your network.
- Check for Firmware Updates: Some modems allow manual firmware checks/updates, usually under Maintenance or Administration.
Belong Modem login in other languages
Popular IPs for Belong
Frequently Asked Questions about Belong
What is Belong?
Belong is an Australian ISP providing NBN services. The modem is the device connecting your home to the NBN and creating your local network.
How to change Belong's WiFi Password or SSID?
Log in, go to Wireless/WiFi settings. Find the field for WPA Pre-Shared Key or WiFi Password and change it. Remember to save.
What if I forget the Belong password?
Perform a factory reset using the reset button. Then log in with the default credentials: IP '10.0.0.138', user 'admin', pass 'Belong'.
Can I change Belong to another IP?
The modem's LAN IP (10.0.0.138) can typically be changed in the LAN settings, but this is rarely necessary for home users.
How to Protect Your WiFi Network Using Belong?
Change the default admin password ('Belong'), use a strong WPA2/WPA3 WiFi password, keep firmware updated if possible.
How to reset your Belong login password?
Resetting erases all custom configurations (WiFi name/password, admin password) and restores the factory defaults.
What are the most common default logins for Belong?
IP: '10.0.0.138', Username: 'admin', Password: 'Belong'.
What is the most common default username for Belong?
The default username is 'admin'.
What is the default password for Belong?
The default password is 'Belong'.
Advanced Belong Router Settings
Belong modems typically offer standard features for home networking:
Dual-Band WiFi
Most models support both 2.4GHz and 5GHz bands for flexibility between range and speed.
DHCP Server
Automatically assigns IP addresses to devices connecting to your network.
NAT and Firewall
Provides basic network address translation and firewall security.
Port Forwarding
Allows specific incoming traffic to reach certain devices on your network (for gaming, servers, etc.).
UPnP (Universal Plug and Play)
Allows devices to automatically configure port forwarding, though sometimes considered a security risk.
Note: Advanced features may vary slightly depending on the specific Technicolor or Sagemcom modem model supplied by Belong.
Explore Other Router Brands
Discover more router brands and their login details